Rental Minimum Standards: The Plumbing Items You Must Meet
The NSW fit-for-habitation and water-efficiency rules that involve plumbing, what they mean in older Shire homes, and how to check a property against them.
By the Cronulla Plumbers teamPublished 12 July 2026
Fit for habitation is the floor, not a wishlist
In New South Wales, a rental property must be fit for habitation, and the law sets out seven minimum standards it has to meet before and during a tenancy. Several of those standards are squarely plumbing, and in the older housing stock of suburbs like Caringbah and Woolooware they are the ones most likely to be marginal. If a property falls short, a tenant can request the repair, escalate to NSW Fair Trading, and apply to NCAT, the NSW Civil and Administrative Tribunal.
This article covers the plumbing-related items in general terms. The full set of standards, including the non-plumbing ones such as structural soundness, lighting, ventilation and electricity supply, along with the separate smoke alarm obligations, is published by NSW Fair Trading, and that is the version to check a property against before a new tenancy starts.
The toilet and bathroom
A property that is fit for habitation must have working bathroom facilities, including a toilet and washing facilities, with privacy, and it must have adequate plumbing and drainage. In practice, a functioning toilet means it fills, flushes and seals properly. A cistern that runs continuously, a pan that rocks on a broken flange, or a base that weeps onto the floor does not meet the spirit of the standard, and each of those is also a repair that gets worse with time.
In older Cronulla and Caringbah units we still find original cisterns with obsolete internal valves. Parts for some of these are no longer made, and the honest fix is a new cistern or suite rather than another temporary washer. We tell property managers plainly when a toilet has reached that point, with photos to send the owner.
Hot and cold water, where it has to be
The premises must be connected to a water supply that can provide hot and cold water for drinking and for washing and cleaning, and that water has to reach the kitchen, the bathroom and any laundry facilities that are provided. Adequate is the operative word. A hot water service that technically works but delivers a trickle of warm water to the shower is a problem, and around here the usual cause is an ageing outdoor hot water unit that the salt air has worked on for years past its prime.
The kitchen must have a sink with hot and cold water in good working order, and the bathroom must have a washbasin and a shower or bath with hot and cold water. If any of these fixtures is present but not working, it is a repair. If hot water fails entirely during a tenancy, that is an urgent repair under the Residential Tenancies Act 2010 (NSW), not a job for next week.
Water efficiency and passing on the water bill
This is the standard NSW property managers most often overlook, because it is tied to money rather than habitability. A landlord can only pass Sydney Water usage charges on to a tenant if the property is separately metered, the charges do not exceed what the landlord is billed, and the property meets the NSW water efficiency measures. Miss the water efficiency measures and the usage charges stay with the owner, tenancy after tenancy.
The long-standing measures are simple. Every shower head must have a flow rate of no more than nine litres a minute, and there can be no leaking taps at the start of the tenancy or once a leak is reported. More recent measures extend the requirement to certain kitchen and bathroom taps and to dual-flush toilets. Older Shire homes often still carry original high-flow shower roses and single-flush pans that predate all of this, so this is worth checking before a lease rather than after. Confirm the current measures with NSW Fair Trading, because the detail has changed over time.
Swapping a shower head or fixing a dripping tap is quick and inexpensive, and it is one of the least costly ways to keep the water charges recoverable. While we are there we check the isolation stops and the state of the tap bodies behind the wall, which in older Shire bathrooms is often the more interesting story.
Laundry connections and the fixtures in between
If laundry facilities are provided, they must be connected to hot and cold water. Old laundries in post-war Caringbah and Woolooware homes frequently have seized or corroded washing machine stops, and a stop that cannot be turned off is a flood waiting for a burst hose. We treat replacing seized laundry stops as basic risk management for any rental, because flexible hose failures are one of the most common causes of internal flooding in tenanted properties.
Beyond the named fixtures, the standards sit alongside the landlord's general obligation to keep the premises in a reasonable state of repair. A dripping tap or a slow drain does not fail a minimum standard on its own, but it is still a repair the tenant can require, it can cost you the recoverable water charges, and it is cheaper dealt with early.
How to check a property before it goes to market
The efficient approach is a single plumbing inspection before a new tenancy, walking the property against the standards and the common failure points of its era. Ours produces a short photo report a property manager can file with the condition report.
- Toilet: fills, flushes, seals, no movement at the base, cistern stops running after refill
- Hot water: unit age, external and salt-air condition, anode and valve check, adequate flow and temperature at every outlet
- Kitchen sink, basin, shower or bath: hot and cold supply working, no leaks underneath
- Water efficiency: shower heads within the flow limit, no leaking taps, dual-flush pans, so Sydney Water usage charges stay recoverable
- Laundry: hot and cold connections sound, stops operable, hoses in good condition
- Drains: no slow runs or gurgling that point to roots in old earthenware lines
Common questions
What happens if a rental is not fit for habitation?
The tenant can require the issue to be fixed, escalate to NSW Fair Trading, and apply to NCAT, and in some cases end the agreement. NSW Fair Trading publishes the process. Practically, it is far cheaper to check and fix before the property is advertised than to deal with it after a tenant has signed.
Can I pass the water bill on to my tenant?
Only if the property is separately metered, the charges do not exceed what Sydney Water bills the owner, and the property meets the NSW water efficiency measures, such as compliant shower heads and no leaking taps. If it does not meet those measures, the usage charges stay with the owner. Check the current measures with NSW Fair Trading.
Can a handyman do these plumbing checks and fixes?
Most plumbing work in NSW, including anything involving water supply, drainage or gas, must legally be done by a licensed plumber. A handyman can change a tap washer in limited cases, but repairs to toilets, hot water systems, pipework and drains are licensed work, and notifiable jobs need a Certificate of Compliance.
